آر اف (فرکانس رادیویی) و بی‌سیم آی سی‌ فرستنده‌گیرنده آر اف

Product Attributes

Introduction

The ADuCRF101 is a fully integrated, data acquisition solution that is designed for low power, wireless applications. It features a 12-bit analog-to-digital converter (ADC), a low power ARM Cortex-M3 processor, a 862 MHz to 928 MHz and 431 MHz to 464 MHz RF transceiver, and Flash/EE memory. The ADuCRF101 is packaged in a 9 mm×9 mm LFCSP. The data acquisition section consists of a 12-bit SAR ADC. The six inputs can be configured in single-ended or differential mode. When configured in single-ended mode, they can be used for ratiometric measurements on sensors that are powered, when required, from the internal low dropout regulator (LDO). An internal battery monitor channel and an on-chip temperature sensor are also available. This wireless data acquisition system is designed to operate in battery-powered applications where low power is critical. The device can be configured in normal operating mode or different low power modes under direct program control. In flexi mode, any peripheral can wake up the device and operate it. In hibernate mode, the internal wake-up timer remains active. In shutdown mode, only an external interrupt can wake up the device. The ADuCRF101 integrates a low power ARM Cortex-M3 processor. It is a 32-bit RISC machine, offering up to 1.25 DMIPS peak performance. The ARM Cortex-M3 processor also has a flexible 14-channel direct memory access (DMA) controller that supports communication peripherals, serial peripheral interface (SPI), UART, and I²C. Also provided on chip are 128 kB of nonvolatile Flash/EE memory and 16 kB of SRAM. A 16 MHz on-chip oscillator generates the system clock. This clock can be internally divided for the processor to operate at a lower frequency, thus saving power. A low power, internal 32 kHz oscillator is available and can be used to clock the four timers, as follows: two general-purpose timers, a wake-up timer, and a system watchdog timer. A range of communication peripherals can be configured, as required, in a specific application. These peripherals include UART, I²C, SPI, GPIO ports, PWM, and RF transceivers. The RF transceiver communicates in the 862 MHz to 928 MHz and 431 MHz to 464 MHz frequency bands using multiple configurations. On-chip factory firmware supports in-circuit serial download via the UART, and nonintrusive emulation and program download are also supported via the serial wire interface. These features are incorporated into a low cost development system supporting this precision analog microcontroller family. The ADuCRF101 operates from 2.2 V to 3.6 V and is specified over an industrial temperature range of -40℃ to +85℃. It is available in a 64-lead LFCSP package.

Features

• Analog input/output (I/O)
• 6-channel, 12-bit SAR ADC
• Single-ended and differential inputs
• Programmable data rate of up to 167 kSPS
• On-chip voltage reference
• Supply range: 2.2 V to 3.6 V
• Power consumption 280 nA in shutdown mode, nonretained state
• 1.9 μA in hibernate mode, processor memory and transceiver memory retained, RF transceiver in sleep mode
• 210 μA/MHz Cortex-M3 dynamic current
• 12.8 mA transceiver in receive mode, Cortex-M3 in hibernate mode
• 9 mA to 32 mA transceiver in transmit mode, Cortex-M3 in hibernate mode
• RF transceiver Frequency bands 862 MHz to 928 MHz, 431 MHz to 464 MHz
• Multiple configurations supported
• Receiver sensitivity, bit error rate (BER) −107.5 dBm at 38.4 kbps, 2FSK
• Single-ended and differential power amplifier (PA)
• Low external bill of materials (BOM)
• 32-bit ARM Cortex-M3 processor
• Serial wire download and debug
• External watch crystal for wake-up timer
• 16 MHz internal oscillator with 8-way, programmable divider
• 128 kB Flash/EE memory, 16 kB SRAM
• 10,000-cycle Flash/EE endurance
• 10-year Flash/EE retention
• In-circuit download via serial wire and UART
• UART, I2C, and SPI serial I/O
• 28-pin GPIO port
• 2 general-purpose, 16-bit timers
• 32-bit wake-up timer
• 16-bit watchdog timer
• 8-channel pulse-width modulation (PWM)
• 64-lead, 9 mm×9 mm LFCSP
• Temperature range: -40℃ to +85℃
• Low cost development system
• Third-party compiler and emulator tool support

Applications

• Battery-powered wireless sensors
• Medical telemetry systems
• Industrial and home automation
• Asset tracking
• Security systems (access systems)
• Health and fitness applications